Plumbing 101: A Guide to Bathtub Installation

Call Today


Everybody will have their private piece of advice with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


How to Install a Bathtub Yourself
Setting up a tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a new one is likewise a moderately hard task. If the old tub is easily obtainable, the project can relocate speedily; if you need to open a wall to eliminate the old bathtub as well as position the brand-new bath tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will need a helper to vacate the old tub as well as set in the new one. Ensure you have actually qualified on your own for the job as well as are comfortable trying it. Instead of working with a service provider to take over a halfway-completed job, it is much better to consider using one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This post will certainly aid you set up a brand-new tub in your restroom if you have actually currently gotten a new bathtub and don't require to transform the setup of your previous water pipes.
Your tools and also material list should consist of the following:


  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  •  

Getting ready for the Installation


Firstly, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to stop pressure on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its final position.



Removing Old Touches


If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome due to the limited accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.



Setting up the Tub


Utilizing both wood boards under its feet, position the bath tub in the required placement. The wood boards are valuable in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bath tub till the level checks out degree.
To mount taps, fit all-time low of the outermost versatile faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the water as well as check all joints as well as brand-new pipework for leaks and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait up until the bath tub has actually been used at the very least when as this will resolve it into its final setting.



Suitable New Touches


If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washers remain in location between the faucet and the sink. Safeguard the faucet in place with the maker provided backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.



Tiling Around the Bath tub


In the area where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to split a rigid seal, creating the water to penetrate the wall surface between the bath and also the tiling, bring about problems with dampness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always load the bathtub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can crack relatively very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof adhesive and grout.


A Step-by-Step Guide to Installing a Bathtub


Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


Remove the Existing Bathtub


To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


Choose the Right Bathtub


The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


Install the Plumbing and Ledger Board


You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


Install the Bathtub


When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


Hook up the Plumbing


Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


Install the Bathtub Surround


A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


Installing A Bathtub


Do you enjoy reading about How to Install a Bathtub Yourself? Leave a short review further down. We'd be glad to know your insights about this post. We are looking forward that you visit us again later on. Loved our piece? Please share it. Let another person locate it. Many thanks for your time. Visit again soon.


Plumbing excellence awaits.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Plumbing 101: A Guide to Bathtub Installation”

Leave a Reply

Gravatar